Using DMR Reflectors on BrandMeister

Update 2018-10-09: Reflector functionality has been removed from US Masters.

In the early days of DMR, mostly in Europe, DMR repeaters used the DMR+ network. This network is reflector based, much like how D-STAR works.

Before getting very far into the discussion, it is important to know there are talkgroups associated with each of the reflectors. The only advantage to a reflector is it’s dynamic nature…being able to use them without programming channels. However, several of the modern DMR radios allow you to manually enter group call IDs, this negates the need for reflectors.

When using a reflector, think about a hub with multiple repeaters (or hotspots) connected. Each repeater sends RF traffic to the reflector and the reflector sends that traffic to all other connected repeaters. A repeater can be connected to only one reflector at a time and anyone using that repeater (on TG9) will be communicating through the same reflector.

You can talk through the connected reflector using Talkgroup 9 on timeslot 2. When no reflector is connected, TG9 operates like a local talkgroup.

Connecting a reflector is fairly easy. Tune your radio to TG9, in many code plugs this will be labeled “Ref” or “Reflector”. You will then issue a private call to one of the reflector numbers. Reflectors are numbered 4001- 4999. If there are reflectors you plan to use frequently, you can add them to your contact list. Most radios will allow you to go into contacts and manual dial a contact.

There are also two special id’s on either side of the reflector range that must be sent as private calls:

  • 4000 – Issuing a private call to 4000 will disconnect a reflector
  • 5000 – Issuing a private call to 5000 will tell you which reflector is connector (or none)

As mentioned above, all reflectors have an associated talkgroup. You can view the list at This list is not very user friendly but you will find entries like this:

4001@TG26312 Berlin-Brandenburg@1@1234
4002@TG26321 Hamburg@1@1234
4003@TG26323 Elbe-Weser@1@1234
4004@TG26361 Hessen@1@1234

Use the “@” to separate fields as follows:

  1. Reflector number
  2. The associated talkgroup and description
  3. Unknown
  4. Unknown

You can also use the BrandMeister web site to see if a reflector is connected. You can view a repeater info page (, replace the ID with your local repeater) and look at the “Slot details” section. This will show you if a reflector is connected, and the reflector number. This works for hotspots as well.

If you have a repeater or hotspot there is some configuration related to reflectors. You can set a default reflector and a timeout to return to the default reflector. You can also manually set or clear a reflector. This is done on the settings page for your repeater or reflector.

The defaults give you no automatic reflector, and not timeout to return to a specific reflector.

  • Active Reflector – set or clear a reflector. Use “0” to clear a connected reflector
  • Default Reflector – Set this to a reflector number to be always connected, or “0” to be not connected.
  • Reflector Timeout – The number of seconds of inactivity before returning to the Default Reflector.

I recommend setting the default to zero and the timeout to a reasonable value (5 minutes). This way, if someone leaves your repeater connected to a busy talkgroup, it will timeout and disconnect.


Join the conversation

comment 8 comments
  • Bill Scholtz

    Can someone make an operator manual for my CSi 800D.
    It’s instruction is only for non-amateur (truckers)

    • af6fb – Orange County, Ca – a guy with a computer, a radio, and a camera


      I’m certain someone could. I have not heard of work that has already been done.

      Do you have specific questions? I might be able to help, send me email.

  • Amos Favorite

    I have Repeater made from two(2) DMR – HT/ Radio Sets it is looped one TX and the other RX and I can talk to other radio sets in the area.

    I am ready to buy a repeater with the minimum requirements to coonect to BrandMeister. Where is the list I have a UHF repeater ham repeater in Baton Rouge, LA. 70810.

    My plan is to connect to the OMIK Talk Group, once the unit is working. I am Up on UHF, VHF repeaters and configuring Motorola mobile radios that are Tear one(1).

    Who can I contact, not interested in a Hot-Spot, a repeater with internet is ok, I have WIFI at the site?

    • af6fb – Orange County, Ca – a guy with a computer, a radio, and a camera


      I don’t completely understand your question.

      Commercial repeaters that support DMR directly are from Motorola or Hytera. Go to and select “Repeaters” in the menu for details. You can also build a repeaters using an MMDVM board and two mobile radios that have 9600 baud (non-discriminated audio) support.

      Both the Hytera and Motorola repeaters have Ethernet connections built in, so they would require an adapter to connect to your Wi-Fi. I recommend the Hytera repeater as you can manage it remotely, the Motorola does not support this.

      I don’t know what you mean by “tear one”. Do you mean Tier 1? For DMR you need a Tier 2 radio.

      Please let me know if I can be of more help.

  • w8eomentor

    Ed Oxer

    using a radioodity gd 77 and 4000 disconnect but sporadically won’t disconnect from tg3100. get a tx fail: carry limited?? what is this?? why doesn’t it work??

    • af6fb – Orange County, Ca – a guy with a computer, a radio, and a camera


      Hmm, not sure. Are you connected to a repeater or a hot spot?

  • Glen Farough

    Where did the 4026 Canada English polular DMR reflector go?

    • af6fb – Orange County, Ca – a guy with a computer, a radio, and a camera


      I don’t know, I can tell you the US masters are no longer offering reflectors.

Leave a Reply Cancel reply

Exit mobile version